全國咨詢熱線
切絲切片機出現異常如何處理?
How to deal with the abnormality of the slicer?
異常情況及處理方案:
Abnormal conditions and handling plan:
1. 絹絲切片機的半成品松弛時，與施膠不均勻、基材不均勻密切相關。這時，應調整弓輥，使其保持平整。
1. The relaxation of semi-finished products of silk slicer is closely related to the uneven sizing and substrate. At this time, the bow roll should be adjusted to keep it flat.
或?qū)⒕硗矎埩υ龃髸r，裁剪機用刀管壓緊基材。
Or when the tension of the drum increases, the cutter presses the base material with a knife tube.
2、半成品在卷繞起皺時，可適當增大張力缸壓力。當卷繞成品運行時，卷繞軸是否張力
2. The pressure of tension cylinder can be increased properly when the semi-finished product is winding and wrinkling. Whether the winding shaft is under tension when the winding finished product is running
緊繃時，或與膠水有密切關系時
When tight or closely related to glue
3.卷取軸張力設定:
3. Coiling shaft tension setting:
卷筒軸上膠帶的張力由張力調節螺母控制。
The tension of the tape on the drum shaft is controlled by the tension adjusting nut.
順時針旋轉螺母，擰緊膠帶，逆時針旋轉螺母。
Turn the nut clockwise, tighten the tape, and turn the nut counterclockwise.
4. 卷取軸處理不均勻:
4. Uneven treatment of coiling shaft:
檢查左右鏈輪是否松脫。
Check whether the left and right sprockets are loose.
B安裝四個繞線軸。側邊機對兩側進行水平調整，并校正位置。通過右內鏈輪兩側的調節螺絲進行調節。
B install the four spools. The side machine makes horizontal adjustment on both sides and corrects the position. Adjust by adjusting screws on both sides of the right inner sprocket.
調整左邊到所需的角度，然后從右邊調整到水平。
First adjust the left side to the desired angle, then adjust the right side to horizontal.
5. 廢卷取及調整:
5. Waste coiling and adjustment:
正確調整磨邊軸上的襯套，使其與磨邊位置對準。
Correctly adjust the bushing on the edging shaft to align with the edging position.
B手動操作，直到有足夠的邊料被卷筒纏住為止。
B operate manually until there is enough leftover material entangled by the drum.
C機器運行時，邊料自動卷取。
C. when the machine is running, the scraps are automatically coiled.
6. 感應開關功能及調節:
6. Induction switch function and regulation:
A本機感應開關為固定點開關，無需調整。
A. the inductive switch of this machine is fixed point switch without adjustment.
反感應:四點感應，三段長度數控線切割。計數器,穩定的剎車,
Anti induction: four point induction, three length CNC wire cutting. Counter, stable brake,
C開關軸感應:每個開關軸一次，計數器累加一次，以計算成品數量。
C switch axis induction: once for each switch axis, the counter accumulates once to calculate the quantity of finished products.
以上就是如何處理切絲切片機的異常情況。如果您有任何其他問題，請隨時聯系我們的24小時客戶服務解答您的所有問題。
The above is how to deal with the abnormal situation of the slicer. If you have any other questions, please feel free to contact our 24-hour customer service to answer all your questions.
