全國咨詢熱線
生產能力：800/1200 kg/h 電機功率：1.5 kW 切菜規格：800/1200 kg/h 尺寸：1300×600×1050 mm/1800×710×103
切片機使用須知及切片效果的保證切片機的外包裝是不銹鋼的，所以我們?cè)谌粘Ｊ褂玫臅r(shí)候，應當特別注意不要使用過尖或者是過硬的東西碰到其表面，以免劃傷。如果在使用一段時間之后，需要對切片機產品進行清洗的時候
The instructions for the use of the slicer and the guarantee of slicing effect the outer package of the slicer is stainless steel, so we should pay special attention not to use too sharp or hard things to touch its surface in daily use, so as not to scratch it. If the slicer product needs to be cleaned after being used for a period of time
切片機的外包裝是不銹鋼的，所以我們?cè)谌粘Ｊ褂玫臅r(shí)候，應當特別注意不要使用過尖或者是過硬的東西碰到其表面，以免劃傷。如果在使用一段時間之后，需要對切片機產品進行清洗的時候，工作人員應當同時卸上下的固定的螺絲，以免在拆掉幾個螺絲的時候，發生危險，或者是損壞設備。
The outer package of the slicer is stainless steel, so we should pay special attention not to use too sharp or hard things to touch its surface in order to avoid scratching. If it is necessary to clean the slicer products after a period of use, the staff should remove the fixed screws at the same time, so as to avoid danger or damage to the equipment when removing several screws.
還要注意對切片機做好潤滑護理，應當定期查看其的潤滑情況，在添加潤滑油的時候，應當保證油量充足，但不要過量。工作人員應當在每天的工作結束之后，及時將切片機內部是所有殘留物料清理干凈。并且要注意檢查刀片的磨損情況，如果有問題的話，應及時修復或者是更換。另外，更好是將工作現場清理干凈，而且要注意切斷設備的總電源。
Also pay attention to the lubrication care of the slicer. Check its lubrication regularly. When adding lubricating oil, ensure that the amount of oil is sufficient, but not excessive. The staff shall clean up all residual materials inside the slicer in time after the end of each day's work. And pay attention to check the wear of the blade. If there is a problem, it should be repaired or replaced in time. In addition, it is better to clean up the work site and pay attention to cutting off the total power supply of the equipment.
總之，在我們使用切片機的時候，不僅需要按照正確的要求進行操作，還應當盡可能為其提供一個衛生的工作條件和工作環境，以保證切片機的工作性能得到充分發揮。
In short, when we use the slicer, we should not only operate according to the correct requirements, but also provide it with a safe and hygienic working condition and working environment as far as possible, so as to ensure that the working performance of the slicer can be brought into full play.
除此之外，要想達到良好的切割效果，還需要做好相關的調節工作，并及時更換磨損的刀片，實現切割效果。調節時先松開固緊銅柱螺母,其次轉動螺母與銅柱上的厚薄方向調節，厚薄調妥后，必須把螺母與銅柱擰緊。
In addition, in order to achieve good cutting effect, it is also necessary to do relevant adjustment work, and replace the worn blade in time to achieve cutting effect. When adjusting, first loosen the nut fixing the copper column, and then rotate the nut to adjust the thickness direction on the copper column. After the thickness is adjusted properly, the nut and the copper column must be tightened.
更換切片機刀片的時候，需要用六角把手插入該機側面孔位，轉動可以調盤方向再換刀；換刀時松掉刀片的二只六角螺絲，插入刀片更換即可，確保切片效果的順利完成。
When replacing the blade of the slicer, it is necessary to insert the hexagonal handle into the hole on the side of the slicer, turn the wheel direction, and then change the blade; When changing the knife, loosen the two hexagon screws of the blade and insert the blade for replacement to ensure the smooth completion of the slicing effect.